• MN-PLCSLM11 street light controller uses power carrier communication to realize the collection and reporting of input and output current / voltage, active power, apparent power, power, frequency, power factor, temperature, and status of switching lights.

• 
  
  The main performance of the controller Features: 

  
  

  1. Size: Length, Width and Height = 100mm * 68mm * 50mm

  2. Parameters: 

• Functional parameters
  Dimming type	0~10V
  	PWM
  Data Collection	Current, Voltage, Frequency
  	Active power, apparent power, reactive power, power factor, electric quantity
  Multiple protection	Multiple protection overvoltage / undervoltage, overcurrent and overload; Warning of abnormal line, driver and lamp; warning of lamp aging;	Cloud configurable
  Remote upgrade	Support firmware remote FOTA	PLC-STA Module
  Edge computing	Smart control, local offline work

  

  Installation instructions:

  It supports multiple installation methods.

  There are two typical installation methods: 

  
  When the controller is installed and placed , wrong wiring and rain water immersion shall be avoided.

  In addition, it should be fixed firmly during installation, and avoid the scratch and insulation damage of the line. 

• 
  

• 
  

  Measurement range and accuracy
  Current	0-12A ±2%
  Voltage	220V ±2%
  Active power	5W~400W
  Power factor	≤ ±0.02
  Electric quantity	±5%
  Temperature	-40~85°；Typical measurement error±1°
  Communication form
  Peak rate	0.507Mbit/s
  Sensitivity	Greater than 0.2mVpp
  Power Consumption	Static chip power consumption is less than or equal to 50mW
  working temperature	-40℃ ～ +85℃
  working voltage	3.3V
  Application Scope
  Usage scenarios	LED driver dimming power supply, LED light
  	Industrial Park, campus, commercial residence, road and municipal street lamp
  	Port, stadium, Airport

• 
  

• Maximum load current:  ＜12A     250VAC

• Maximum load power consumption:  ≤400W

• Voltage supply  AC: 90～264V

• Frequency 50～60Hz

• AC Parameters

• Load Parameter: 

• Controller power consumption: ＜2W 

•  PLC (Power Line Carrier Communication) technology; 

•  0-10V, PWM dimming output at the same time; 

• The success rate of a single network connection is above 99.9%; 

• Achieve multi-function detection of current / voltage, active power, apparent power, power, frequency, power factor, etc .; 

• High-precision data acquisition scheme, meeting national metering standards; 

• channel 10% ~ 100% arbitrary ratio 1-10V / PWM stepless dimming output function; 

• Support controller temperature detection, real-time monitoring of the use environment temperature;

• Over-current / over-voltage / under-voltage, overload protection, lamp condition and line detection, default lighting, etc .;

• Active reporting of various faults; including lights, drivers, line faults, etc .;

• Support various custom network analysis data collection functions;

• Load lightweight system RTOS, support data concurrent fault tolerance function, cell reselection, inter-frequency networking, remote upgrade ...

• Suitable for switching and dimming of various power LED lights and lamps; support multiple power-off modes of power driver and line input relay;

• Safety-based overload protection design;

• Support zero crossing detection switch light;

• Edge computing, support local policies; network abnormal / no network status automatically executes cloud configuration policies locally;

• Support timing switch, time control mode;

• Plug and play, support scanning installation registration;        

• Industrial grade working temperature: -40 ℃ ～ ＋ 85 ℃;

• IP66 waterproof rating; ? High lightning protection level ± 6KV (line-to-line);

• Respond to the instructions sent by the center within 3 seconds; 

For any questions, or if need any further information, please contact us freely!

Email: sale2@micronature.cn